[Set] Aeroknox AX//15 MWS Gas BlowBack rifle - Black [DE] + 35rd Green gas magazine for Noveske N4 MWS - Black [DE]

For everyone wanting to buy magazines for your mws. DO NOT BUY THE DMAGS V1 or V2.
After some time, the magazines starts leaking while inserting gas from inside and the gas realse valve are broking. You can try using the youtube video from SPEARHEAD GROUP to fix the first issue but it’s only temporarily. Buy the Double Eagle STANAGS, they are the best magazines to buy for MWS. If they are temporary inavaiable just wait, it’s worth it.

I bought 2 of this magazines and both of them liking, loosing gas, also for some reason with this magazines the joules goes down to 0.87 and fps 265, with other magazines I have 1.25 joules, I’m so disappointed with this magazines , doesn’t worth the money . First of all they must be check the magazine before sending to the customers, that is the Biggest wrong.
I can’t play with this magazines are useless.
Nice design fit perfectly with noveske n4 but I’m not recommending.

I ordered three of the magazines. In terms of looks and feel they seemed good, with nice material quality, but two out of the three are leaking. It’s possible that a cleaning will help, but it may be necessary to replace the valve.

The gas efficiency of the mag is very good, and it's great that the refill valve is located right beneath the release valve rather than at the bottom of the magazine. If you prefer using open mag pouches, this design makes life easier, as it reduces the chance of dirt getting into the refill valve

Shoots really well nice kick for sure.
Came very oild up seemed like silicon oil and was a little dirty. Factory dirt? Maybe cleaned the bolt and the upper and put some ptfe grease instead shoots better and feels nicer in the bolt.
Having a hard time for my mag to hold gas for more than 1.5mag but that may just be my gault using the wrong kinda gas?

Pros
-shoots well
-locks without issue
-nice kick
-nice metallic finish
-steel internals
-nice weight
-mag not to heavy nice weight
-easy to handle
-good length and the bump in the rail is perfect for pressure pad

Cons
-came a little to dirty bolt was a little sluggish (but not hard to clean so not that big of a con
-Having hard time to get more then 1.5mag out of with gas (maybe using the wrong gas
-shoots a little hot you do need and npas in this

Back after actually using it for about 1500-2000 rounds. Externally the replica has held up very well. No wear or tear has formed besides some scratching on the buffer tube from replacing a few stocks. The selector switch did vibrate loose at some point, but after tightening the screw this hasnt happened again. The standard stock rattled a small bit so I replaced it with a replica CTR.

Internally this replica really did need an Npas. Even with lower power gas I could not get the output to below 1.4J. installing an Npas is simple though so no issues there. However it would be cool if Taiwangun were to stock Npasses and other GBB parts. Replica came well greased on the triggerbox however the bolt was nearly dry.

Barrel is fine. No need to replace it. So far the hop has held up perfectly fine, though with .32G bb's replacing the arm and bucking may be a nice idea down the line seeing as the hop is nearly maxed. Magazine wise I tested the DE stanag and TM stanag. Both have worked flawlessly for me outside of 1 jam with the DE Stanag.

All in all a great replica. Besides an Npas I wouldnt make any modifications until something breaks.
Very satisfied :)

Easy durable polymer, I had no issue with gasleak so far, however I prefer the stanag version.
Pros:
+Easey to carry on your rig
+No leaks so far
+Durable, already dropped in mud on concrate and works like a horse.
+It is always on stock

Cons:
-Gas Efficiency is not as good as DMAG-B2.
-Kickback is not as powefull as DMAG-B2

Externally the gun feels and looks amazing, For me it came with a nicer pistol grip than shown in the pictures on the site. Stock is way less wobbly than on the Noveske to the point where I consider leaving it on there cause it looks quite good.

Internally I am new to GBBRs so I cant say too much. I can however verify that the model I received works perfectly with Tokyo Marui Stanag magazines. The replica came very well lubricated. The gun does require an NPAS or very low power gas though. It comes in at 1.8J with .32 BBs. Internally everything looks good to me. It shoots straight even with the standard bucking.
For anyone considering this replica, Jeager Precision sells an NPAS that should fit the defealt DE nozzle.

All around amazing gun with an amazing feel.

Parfaitement compatible avec le Ghetto Blaster DE, le chargeur est robuste et donne une impression visuelle de qualité. Il feed très bien, sa réserve de gaz permet de tirer les 35 bb's, mais pas un 3 ème chargeur complet. le débit de gaz est plus stable que le chargeur d'origine du Guetto blaster.
A noter que dans mon cas, j'ai dû rajouter un joint à l'extérieur de la valve de remplissage pour supprimer les fuites lors du changement avec la bouteille de green gaz.
Comme beaucoup de chargeur gbbr compatible MWS, le chargement avec un speed loader est pénible mais peut être grandement facilité en imprimant un adaptateur compatible MWS facilement trouvable sur Cult 3D ou Thingiverse.

I have two mags and one is good and the other one is somewhat low pressured idk, like no matter what gas i put it's low. Maybe production error. Stanag mags are much better and efficient like the one that comes with the replica.

Really good Mag feel solid and sturdy.
I used them on my DE/EMG N4 Noveske.
A bit hard to load in when first loading but with a proper speed loader adapter there are no issues.
The mags came well packed no damage

I just bought a couple of these mags, for my TM MTR(mws) works perfectly if you grind it a sides a bit. So not a big deal to make it good, but anyway looks great, feels good too. grind it a bit of sides and enjoy

Mags work good, but this does not fit the TOKYO MARUI MWS!!!!!
Care when buying for TOKYO MARUI MWS, the top of the magazine is too wide so it doesnt fit, or you will have to file down for it to make it fit.