[Ensemble] CM.701C-U Upgraded Version 520 FPS - Wooden Style [CYMA] + Lunette de visée 3-9x40 avec anneaux de montage haut

J’ai acheter cette lunette équipée sur le fameux lt-20T (barrete) lunette incroyable simple a régler très précise pour le prix j’en suis pas déçu avec TaiwanGun pas obliger de ce ruiner pour avoir de la qualité je recommande rapport qualité prix on et au top je recommande livraison très rapide matériel très bien protéger je profiterais a l’avenir pour reprendre du matériel !

Hi i'm into airsoft since 1997 and i have/ had so many guns.
This replica is very good for is price.
I use 0.50 bls stainless powder.
It's great.

But, my vsr go for 540 fps not 570.
This is the only disappointment cuz i really want to use it for plinking with is max potential.

Too bad.
Great gun otherwise

Bon viseur, j'ai eu du mal à m'habituer au début mais une fois qu'on s'y fait c'est top.
Fournis avec un cache jaune pour éviter que la lumière réfléchisse sur la lunette.
Fournis avec un monte rail, facile a monter.

J'en suis satisfait.

Agréablement surpris, même pour de l'abs, le corps en imitation , je le trouve magnifique la prise en main assez intuitive, mécanisme plutôt souple, aspect général rien signalé. Niveau poids c'est plus ue correct. Pas déçut de mon achat , interne full vsr10 donc aucun soucis pour avoir de la pièce détacher pour l'entretiens

Très bonne lunette pour un prix abordable. Il a un zoom 3 - 9 x. Je l’utilise sur mon fusil de sniper et je suis vraiment impressionné. Jusqu’à présent, les rayures minimales sur la peinture extérieure et la lentille sont claires. Il est également livré avec un couvercle de protection pour lentilles afin qu’il ne se raye pas pendant le stockage.

Lunette facile a mettre en place. Monter sur ma "mb01 coyote" qui est doté du raille adapté. Relativement simple a calibrer. Et bonne visibilité. Arrivé relativement rapidement en considérant la distance. Pour moi c'est parfait rien a en redire!

Lunettes de bonne qualitée elle est perfomante et son zoom est efficace je la reccomande pour ceyx qui cherche une lunette a bas prix pour ceux qui commence l'airsoft tres bon rapport qualité prix. Je reccomande ce produit.

The gun was not usable upon arrival. I couldn’t properly insert the magazine because one of the internal parts was loose. One of the hex screws in the stock was just spinning freely—it was already stripped along with its thread from the start. I had to completely disassemble the gun and fix it with some help. Based on my first impressions, the build quality is not the best. It delivers the advertised FPS, but how well it will hold up in the long term is questionable.

I’ve been using this 3-9x40 scope with high mount rings on my airsoft rifle for a few game days now and overall it does exactly what it’s supposed to do. The glass is surprisingly clear for this price range and target acquisition at mid-range is comfortable even at lower zoom settings.

The 3-9x magnification range is actually quite practical in the field — I mostly run it around 4-6x and only crank it up when I really need to confirm hits at distance. The included high mount rings make installation easy and give enough clearance for comfortable cheek positioning, even on standard RIS rails.

Build quality feels solid enough for airsoft use, the body doesn’t feel flimsy and so far it has held zero without any noticeable drifting after multiple games. Adjustments for windage and elevation are responsive and predictable, nothing overly stiff or loose.

Overall it’s a simple, no-nonsense optic that won’t compete with high-end glass, but for airsoft skirmishes it delivers reliable performance and good clarity for the price. Definitely a solid upgrade over basic iron sights or cheap red dots.

Very good performance, 522FPS with 0.2 bbs. Solid replica, came with 3 mags (description mentions 1 tho) and a speed loader. Easy to pull the handle, but still powerful. Only downside is that the trigger is very wobbley. Moves too much, i will take it apart and take a look at it. I recommend this gun to everyone, it’s a vsr-10 compatible gun, lot of aftermarket parts to choose from.

4 days shipping, good customer service as always, keep it up Taiwangun! Have a good one

The CYMA CM.701 is an amazing starter sniper rifle, especially for the price. Out of the box, it’s solidly built with a sturdy bolt action and decent power. What really makes it shine is the huge upgrade potential — it’s fully VSR-10 compatible, so you can easily swap in better barrels, hop-up units, and triggers to make it competition-ready.

For under $100, you’re getting a reliable rifle that’s perfect for beginners or experienced players looking for a modding project. Highly recommended if you want great performance on a budget and a strong base to build from!

IMO the best bang for the buck, especially on sale; and it doesn't take much to turn it into a laser. But let's go over the externals first.

The wood imitation is great, doesnt have that cheap plastic feel, isn't glossy, it's actually really well made. The outer barrel is some kind of metal (most probably steel), along with the receiver, coated with a black matt paint. The barrel is threaded although i just cannot get the end cap to come off, it's glued shut, pretty sure i could get it open if i tried hard enough, BUT, even if you do, you need an adapter to mount your standard CCW 14mm thread muzzle devices, luckily Taiwangun also sells one so you can get it along with the rifle. The charging handle is not as well made tho, not like it's gonna crack or something but it's very wobbly, personally, i dont mind that much, but i know some people will so i thought i should point it out.


Now for the internals, the trigger is great, very light and snappy, everything you would expect from a 90° trigger really. The rest, isn't perfect, but there are some easy fixes. The cylinder is very loose inside the outer barrel, so it scratches against the walls making the bolt pull very rough.

Fix: get a piece of a plastic notebook cover or a PLA plate, cut it to fit the inner barrel part where the piston slides in without standing out the back, beware not to cover up the hole that feeds the BBs into the chamber; use some PTFE grease and that should do it. You can also look up some other tutorials for smooth bolt pull on YouTube.


The pneumatics... there is some compression but they leave much to be desired.

Fix: Screw off the cylinder head, apply teflon tape to the thread, before putting it back in place, take out the piston, cut a piece of electric or teflon tape, roll it up to fit the groove where the O-Ring goes on the piston, put the O-Ring back in place, apply some silicone grease and test if it fits into the cylinder. If it doesn't, get a smaller piece of tape, test and repeat until it goes in with some resistance, but not enough to rip the O-Ring. Even after that, it doesn't seal 100% but it's definitely better than it was stock.

Precision components, the barrel, chamber and bucking are okay. 0.40g BBs are the heaviest i managed to lift. Stock, it shot at around 2.1 Joule (measured with 0.40g BLS) and i could hit a human torso at about 50-60 meters with some inconsistencies.

Fix: Maple Leaf 430mm 6.02 inner barrel, Maple Leaf VSR10 chamber and Maple Leaf 70° Autobot. Total cost comes at around $50 (all available on this site).

All those upgrades gave me fairly consistent 2.5 Joules and range of 70+ meters (0.40g BLS). I'm not sure about the maximum range since i fired at a torso sized target at those 70m and the BBs were still flying straight :)


To sum things up; it's an okay rifle out of the box, with really well made externals and tons of potential for upgrades.

Overall, very satisfied with the gun :)

IMO the best bang for the buck, especially on sale; and it doesn't take much to turn it into a laser. But let's go over the externals first.

The wood imitation is great, doesnt have that cheap plastic feel, isn't glossy, it's actually really well made. The outer barrel is some kind of metal (most probably steel), along with the receiver, coated with a black matt paint. The barrel is threaded although i just cannot get the end cap to come off, it's glued shut, pretty sure i could get it open if i tried hard enough, BUT, even if you do, you need an adapter to mount your standard CCW 14mm thread muzzle devices, luckily Taiwangun also sells one so you can get it along with the rifle. The charging handle is not as well made tho, not like it's gonna crack or something but it's very wobbly, personally, i dont mind that much, but i know some people will so i thought i should point it out.


Now for the internals, the trigger is great, very light and snappy, everything you would expect from a 90° trigger really. The rest, isn't perfect, but there are some easy fixes. The cylinder is very loose inside the outer barrel, so it scratches against the walls making the bolt pull very rough.

Fix: get a piece of a plastic notebook cover or a PLA plate, cut it to fit the inner barrel part where the piston slides in without standing out the back, beware not to cover up the hole that feeds the BBs into the chamber; use some PTFE grease and that should do it. You can also look up some other tutorials for smooth bolt pull on YouTube.


The pneumatics... there is some compression but they leave much to be desired.

Fix: Screw off the cylinder head, apply teflon tape to the thread, before putting it back in place, take out the piston, cut a piece of electric or teflon tape, roll it up to fit the groove where the O-Ring goes on the piston, put the O-Ring back in place, apply some silicone grease and test if it fits into the cylinder. If it doesn't, get a smaller piece of tape, test and repeat until it goes in with some resistance, but not enough to rip the O-Ring. Even after that, it doesn't seal 100% but it's definitely better than it was stock.

Precision components, the barrel, chamber and bucking are okay. 0.40g BBs are the heaviest i managed to lift. Stock, it shot at around 2.1 Joule (measured with 0.40g BLS) and i could hit a human torso at about 50-60 meters with some inconsistencies.

Fix: Maple Leaf 430mm 6.02 inner barrel, Maple Leaf VSR10 chamber and Maple Leaf 70° Autobot. Total cost comes at around $50 (all available on this site).

All those upgrades gave me fairly consistent 2.5 Joules and range of 70+ meters (0.40g BLS). I'm not sure about the maximum range since i fired at a torso sized target at those 70m and the BBs were still flying straight :)


To sum things up; it's an okay rifle out of the box, with really well made externals and tons of potential for upgrades.

Very satisfied with the gun :)

I chose the wood color. The barrel is plastic, but the imitation of wood is a real eye-catcher. It's a beautiful sniper rifle. It doesn't creak or crack. If you want to put a carrying strap on it, you'll need a converter. The holes in the factory mounting points are tiny, so it's not suitable for a high-quality carabiner. You get two extra springs in the box. I can't wait to put the scope on it and see how it shoots. Double Bell has a similar vsr-10 replica with real wood for a little more money. However, there are hardly any accessories for it. Cyma's tuning options are almost unlimited, so I chose this one.

Really good sniper rifle! The only problem I had with it is the magazine release button is made out of cheap plastic and it broke, making it difficult, but not impossible to remove. Overall, the range and FPS are unmatched at this price with 0.4g bbs.

Really good sniper rifle! The only problem I had with it is the magazine release button is made out of cheap plastic and it broke, making it difficult, but not impossible to remove. Overall, the range and FPS are unmatched with 0.4g bbs.

Cool scope woud recommend.

“The 3-9x40 scope is fantastic for airsoft sniping. Crisp, clear optics at all zoom levels, and adjusting the magnification is smooth. Holds zero well, even in intense games. Great value for added precision!”

The scope is very clear. The adjustable zoom works really well to. Setting it up on your airsoft is very easy to. Then adjust the rectangular sight according to your airsoft bij 2 screws hidden under the aluminum caps. Full aluminum, top quality for a small price.

This was my first sniper rifle,and it has pleasantly surprised me. It has a really good look,and feels like the real thing. Good weigt,its not a light weight rifle.The polymer handle really looks like wood also. The rest off the rifle is made of metal. In combination with a scope you can get pretty accurate shots. It also has an adjustable hop up lever thats easy accessible from the left side of the rifle
One thing you should look out for,is that you pull the lever to load the bibi firmly in one go. If you don't use enough pulling power,and release it before it tensioned the spring,it loads the bibi already,but it won't fire obviously. So you automatically do it again,but then you load a second bibi, and may potentially clog the barrel. But that's not a rifle error,but a human error. So make sure to firmly pull it. If you do clog it,there is a usefully tool in the box to clear the barrel from stuck bibi's. In the box you find 3 magazines. These are plastic, but does work pretty well,and sits flush in the rifle. It won't stick out from under it what I realy like. To release it simply press a button. You also recieve 2 extra spring to adjust the fps,this is realy a nice option as well. This rifle for the money is realy good in my opinion, and you won't regret buying it. Delivery is on point as well. Packed well,and they keep you updated all the way to your doorstep.

This is a very nice nice sniper replica. Most people go for the black one instead. It is always sold out. But i really like the brown one. Gives a different touch to it. The accuracy and precision on this thing is insanely good for the price. Thank you Taiwangun!

Buy this on sale. I use this on AUG(au-1g j.g. works)
Looks really cool and awesome. Very good materials and zoom.
Plus:
+price
+materials
+strong mounts
+hexagon and small cloth for wiping lenses
+clear image

Minus:
I don't see minuses for this things, for now:)

Good value for money starter sniper.
Especially with the upgraded parts, so solid base, solid parts and as always checked by Taiwangun.
3 mags included!! 2 extra springs and shoots as ordered and advertised.
5/5

I would say that a scope is essential for sniping, and this one is amazing. The variable zoom feature is amazing because the enemy can be in different distances, and the zoom feature makes it easier to engage the enemy. It is sturdy and doesn’t rattle, the windage is easy to adjust.

4/5 nothing special but still amazing

The product is perfect value for money. Adjustable focus, easy to mount, gives a clear image. Note that it does not magnify, but adjusts the focus, so close objects are blurred.

Ár-érték arányban tökéletes a termék. Állítható a fókusza, könnyű felszerelni, tiszta képet ad. Arra kell figyelni, hogy nem nagyít, hanem fókuszt állít, és emiatt a távoli objektumok "közelebbinek" tűnnek, de a közeliek homályosak.

I have used it 5 times , it shoots in a nice curve, I am completely satisfied with it. I chose the wood type, I really like its design. I recommend it to all beginners and non-beginner snipers for airsoft games, it stands up to its bigger names

Scope is great, it helped me a lot in airsoft games I love sniping and fast moving airsoft games so I bought this scope for my m4 from Taiwangun it super good lens are clear and have great zoom. I hope for this review helped someone who want to buy one.

Scope is compleatly clear, has good eye relief and has adjustable zoom 3-9x it is really useful if you want a closer look on someone, if they are on your team or not. Scope can be adjusted down to 0.1MOA that is 1cm at a distance of 100m. I highly recomend this scope for a sniper, this is a super budget friendly option.

9/10.
Out of the box gives 3,1 J while still very easy to operate. Easy 80 m gun, possibly 100 with proper flat hop. Internal trigger mechanism is steel, piston however aluminium using 45° system. Piston will eventually wear out but I would suggest swapping for steel only in case of breakage.
Holding it gives you surprisingly solid feel.
Excellent value.

Good one with this price.!!!!!!!!!!!!! 5 Star

This Replica is really amazing. This is very good choice if you dont want to spend a lot of money.
This upgrade is really powerfull, and you can feel the different between the original one. I think this rifle can be good starter weapon.
Thank you so much!

A budget sniper scope, that is good looking and great for this price. The zoom on it is simply amazing. Build quality is wery good, and is very easy to mount.
Simply an amazing budget scope to start with!!

Very good gun for an affordable price. It has 3 - 9 x zoom. I use it on my sniper rifle and am really impressed. So far minimum scratches on the outside paint and the lens is clear. It also comes with a protective lens cover so it doesn't scratch during storage.

Amazing scope for a good price! I use this on my Cyma Cm702 platform and I could not be happier. The scope comes with two ring mounts and a bag of hex keys to install it. The scope is not too heavy so it does not add significant weight to the gun (which is an important thing for me).

[Color]

Painted black aluminium, doesnt seem to scratch easily.

[Quality]

Very nice quality and the protective caps help alot!
The magnify is really nice, a bit of difficult to set it up with the screw and unscrew but you can work around with some 3D prints!

[Use]

Overall nice usage on a sniper rifle!
5 STAR for sure !

A good scope for a low cost. The lens goes from 3 to 9 and everything in between making it a great scope in many situations. It comes with a protective caps with also will cut your costs. It does have a yellow undertone but makes the targets beter visible under darker situation.