[Ensemble] Cache de tube a gaz AK russe léger - Black [5KU] + Garde main tactique russe pour AK - Black [5KU]

Produit de bonne qualité mais sans aucun marquage et ça c’est dommage.
S’adapte parfaitement sur une réplique LCT ou GHK mais demande un peu de modification pour s’adapter parfaitement tube d’emprunt des gaz d’une AK de Specna Arms.
——-
Good quality product but without any marking and that's a pity.
Fits perfectly on an LCT or GHK replica but requires a little modification to fit perfectly on Specna Arms AK gaz tube.
——-
Produkt dobrej jakości, ale bez żadnych oznaczeń, a szkoda.
Idealnie pasuje do repliki LCT lub GHK, ale wymaga niewielkiej modyfikacji, aby idealnie pasował do rury gazowej AK Specna Arms.

Super produit 5ku.
Le garde main est full métal. Matériaux de qualité pour un prix défiant toute concurrence. S’adapte très bien aux AK 105 GHK pour un style Zenitco.

Great 5ku product.
The handguard is full metal. Quality materials for an unbeatable price. It fits very well to AK 105 by GHK for a Zenitco style.

Super produit ! De très bonne qualité ! Bien fini ! Le tout en alu ! Jolis marquages qui ajoute du cachet a la réplique ! S'adapte parfaitement sur Cyma CM077A ! Aucun jeu constaté. Attention cependant, les arrêtes sont assez aiguisées, protégez vous les mains. Merci Taiwangun pour le produit et la rapidité d'envoi.

RiS Pasuje do prawdziwego AKM, zero luzów, wystarczy przykręcić większe oparcie do Ris (jest w zestawie) obudowę pod komorą nabojową, delikatnie zeszlifowac narożniki i wchodzi idealnie. POLECAM

Stabilna konstrukcja bez luzów po zamontowaniu, bardzo lekka.

Brak.

Solid, Heavy, very heavy handguard but the quality and finish... the best, even LCT can't do it better.

Fitting requires some work but just go to original zenitco youtube channel for installation video and you will see - it have to be hammered in.
With airsoft replica I would sand it a little bit to fit or carefully use dremel and then hammer and then it sits super tight.

With E&L I had to use spacers on frontguard retainer (not included) to make it sit tight because it's shorter than original E&L Handguard.

If you don't mind the weight - that the best handguard for ak!

*Tested on E&L AK-74M
I HIGHLY RECOMMEND THIS HANDGUARD
However, few things first. IF you are putting this handguard on E&L get ready for some serious dremel work.
The areas that need to be ground down are:
1. The small piece that goes inside of the recever needs witdh adjustment on the sides. Roughly 0.5mm in total on both sides to be hammered in properly.
2. The shroud of the handguard around the front tronion (rear sight block) is too thick and needs to be ground down slightly for handguard to be installed properly.
3. Slightly below the handguard shroud is a barrel shroud that isn't wide enough to to fit the barrel. Use a round grind weel to make a cut out for barrel to fit.

Besides that handguard is of good quality and I can recommend it for E&L essential series. As Long as you are willing to put in the work.

Bought it for my E&L ak105. Quite nice quality, feels a bit sharp on the edges, had some clips mounted on rail to protect my fingers. If u want to install this on a E&L ak105 prepare your heart for some work. My solution till this challenge and the three things has to made to be able to fit.
1: The small block(for the rear) that is included wont fit. Took some measurement and 3D printed a custom block for that cause.
2: The rear part of the handguard wont fit enitrely, solution = small surgery with dremel or if u have a circular file.
3: The front of handguard will have some space to fill, i used some stiff rubber.
The gas tube cover for this handguard need also some tiny cut with dremel, probably a file is enough. Tiny adjustment of the front of the gas tube is needed. It hits the front sight = unable to inline with the screws.
Now it sits as a mountain. It cost a small fortune but looks awesome! :D

As all 5KU products this is nicely machined from aluminum and has a nice and durable black finish, thus resulting in a great accessory.
It fits well onto my Cyma AKM and works very well with the matching lower handguard.

The replica has a really nice quality, good paint, nice finish. I installed it on my cyma cm.040D, it had a wobble that I could reduce with some electrical tape, but it was a bit of a pain to get rid of that. I would like to see if someone could manage to fix that entirely.

Bought this one together with lower handguard, fit & finish is nice, but on some LCT replicas you might need to adjust the gas tube a little bit to fit this handguard properly. After fitting it holds rock solid

Good quality. I insert this to my LCT RPK-74 and it was a little challenge. It was possible when you have the rigth tools to modify. If your planning to insert this to LCT AK, you migth have to use dremel too.