[Set] Tactical russian AK gas tube cover - Black [5KU] + Tactical russian AK lower handguard long - Black [5KU]

De muy buena calidad, encaja perfectamente con mi Replica de E&L y no da algunas. Fácil de montar y adaptable a una gran bariedad de marcas de ak. Viene muy bien empaquetado y muy protegido. Calidad precio increíbles

Ta część także pasuje do prawdziwego AKM jest to świetne uzupełnienie, do łoża RiS B30, zero luzów.

Pasuje bez problemu do prawdziwej broni palnej, razem z łożem RiS B30

Brak

RiS Pasuje do prawdziwego AKM, zero luzów, wystarczy przykręcić większe oparcie do Ris (jest w zestawie) obudowę pod komorą nabojową, delikatnie zeszlifowac narożniki i wchodzi idealnie. POLECAM

Stabilna konstrukcja bez luzów po zamontowaniu, bardzo lekka.

Brak.

Solid, Heavy, very heavy handguard but the quality and finish... the best, even LCT can't do it better.

Fitting requires some work but just go to original zenitco youtube channel for installation video and you will see - it have to be hammered in.
With airsoft replica I would sand it a little bit to fit or carefully use dremel and then hammer and then it sits super tight.

With E&L I had to use spacers on frontguard retainer (not included) to make it sit tight because it's shorter than original E&L Handguard.

If you don't mind the weight - that the best handguard for ak!

*Tested on E&L AK-74M
I HIGHLY RECOMMEND THIS HANDGUARD
However, few things first. IF you are putting this handguard on E&L get ready for some serious dremel work.
The areas that need to be ground down are:
1. The small piece that goes inside of the recever needs witdh adjustment on the sides. Roughly 0.5mm in total on both sides to be hammered in properly.
2. The shroud of the handguard around the front tronion (rear sight block) is too thick and needs to be ground down slightly for handguard to be installed properly.
3. Slightly below the handguard shroud is a barrel shroud that isn't wide enough to to fit the barrel. Use a round grind weel to make a cut out for barrel to fit.

Besides that handguard is of good quality and I can recommend it for E&L essential series. As Long as you are willing to put in the work.

Bought it for my E&L ak105. Quite nice quality, feels a bit sharp on the edges, had some clips mounted on rail to protect my fingers. If u want to install this on a E&L ak105 prepare your heart for some work. My solution till this challenge and the three things has to made to be able to fit.
1: The small block(for the rear) that is included wont fit. Took some measurement and 3D printed a custom block for that cause.
2: The rear part of the handguard wont fit enitrely, solution = small surgery with dremel or if u have a circular file.
3: The front of handguard will have some space to fill, i used some stiff rubber.
The gas tube cover for this handguard need also some tiny cut with dremel, probably a file is enough. Tiny adjustment of the front of the gas tube is needed. It hits the front sight = unable to inline with the screws.
Now it sits as a mountain. It cost a small fortune but looks awesome! :D

The replica has a really nice quality, good paint, nice finish. I installed it on my cyma cm.040D, it had a wobble that I could reduce with some electrical tape, but it was a bit of a pain to get rid of that. I would like to see if someone could manage to fix that entirely.

Looks amazing and the markings look almost like the real ZenitCo ones. It's extremely light and it adds some space for attachments on your gun. I paired it with a 5KU-225 lower handguard on an Arcturus PP-19. This part is probably the most universal one which you'll buy since it doesn't require any modifications to fit.

I bought this with a B-11 handguard, the intention was to attach it to a WE AKS74UN, but i changed this part out with the stock upper handguard, because this would make the whole front wobble, i guess you could shim it to fit, but the backplate on the gas tube will sit loose since there's nothing for it to sit on.

The build quality is really nice, and it sits very tight on a B-11 handguard.

Good quality. I insert this to my LCT RPK-74 and it was a little challenge. It was possible when you have the rigth tools to modify. If your planning to insert this to LCT AK, you migth have to use dremel too.

Very good quality. Its a good combo with Tactical russian AK lower handguard. Works well with my Cyma AK. Great to mount cams and/or recticles.
Pros: Its not plastic, so its durable
Cons: Non that I can say, works as intended