KAR98K Cartridges Stripper [Double Bell]

I'm satisfied, it's a nice replica of the real mauser stripper clips. However I found mine to be a bit loose and wobbly with the double bell k98 cartridges. It does require some practice pushing down on the cartridges too, but in the end it's a better reloading method as opposed to loading them single in an airsoft match.

Se adapta fantástico, se carga rápido y sujeta bien los cartuchos. Un complemento muy recomendable a la compra del Kar98k, en caso de querer usar la réplica para airsoft histórico complementa tanto estética como tácticamente

Réplica de peines perfectos, la calidad es asombrosa y el peso igual, las vainas caben sin problemas, siempre es adecuado lubricar antes de cada partida (con una vez basta) la extracción es suave sin impedimentos, lastima que no vayan incluidos en el pack de vainas, aun así vale la pena para no llevar las vainas sueltas, engancha perfecto y descargar sin problemas dentro de la réplica,en ambiente funcional van de maravilla

Se adpta perfectamente a los cartuchos sin olguras.
En la pagina del fusil k98 deberia expecificar que no viene el clip con los cartuchos, la foto llama a equivocarse y tener que pedirlo posteriormente.

Completely unusable spring is too soft and made from some copper or brass alloy and it gives 0 tension causing the shells to sit very loosely making it impossible to load them in the gun
If you are thinking of buying them skip them and buy some cheap Yugoslavian Mauser stripper clips they are cheaper and should work as advertised

the spring material is too soft and because there is no tension the shells dont sit right and wobble a lot which makes it impossible to use
if anyone is thinking of buying them i suggest buying the real life mauser stripper clips they work better and you can also get them at a better price

I did hesitate a lot before buying this item because of the comments.. I do have a real ammo and a real clip for the real Kar98 and spring strength and how it holds the bullets is almost the same.. the quality of the build is pretty good.. great item to buy I highly recommend it.. it's fits the Kar98 double bell really well and it works as intended with no issues.. thank you Taiwan gun team, looking forward for the next purchase...

It's okay. Not the best, but at least is cheap.
Abszolút rendben van, nem nagy szám, de olcsó.

Skip it, the clips do not fit the the gun and even some of them are too loose that bullets might fall off from them.

I used hammer and other tools to tighten it a little bit so the shells at least won't fall but still it is not worth the price.

I have to add one more thing; it doesn't fit on the gun and it is impossible to push the shells into the gun! The shells move in every direction and can easily fall off the clip. I am very disappointed by this clip, it's a waste of money! I bought the Double Bell Kar98 but this clip doesn't fit on it....

The inner metal piece is very loose and moves back and forth all the time. The shells don't fit weel, they can easily fall off the stripper (this happened twice while I was trying to load it). I don't know if the other strippers are the same but mine is not what I expected.

Solid, sturdy clips.
The shells fit nicely and it drastically decreases the time needed to reload.

Clips can be inserted into the gun using the dedicated slot for the clips. I would advise to press down near the back of the shells, it will make it a lot easier.

The shells themselves sit a bit loose in the clip, but since this not a gun to take to a skrim, it should be not a problem.

Note: these clips cannot be used when the scope is mounted! The scope sits 1 cm too far back to be able to use the shells.
If the scope is mounted, load shells individually.

Very cool addition to the shells and double bell kar98k. Loading the stripper/clip is very easy and satisfying.

After the stripper/clip is loaded, you can open the bolt of your double bell kar98k. There is a small slide where you can slide in the clip itself, This can be a hassle at first, but I recommend oiling this up.

After the stripper/clip with shells is in place, you can push down the shells. This as well requires getting used to, put your finger to the middle/backside of the upper shell, and push down until all shells are in the magazine. after that you can remove the stripper/clip and push the bolt forward.

Shells feel amazing to the touch. They are machined very precisely.

When entering the double bell kar98k they make a nice whizzz noise, very cool.

Shells eject nicely when pulling the bolt at a specific speed. I recommend oiling the shells up a little bit and putting a little oil on the tip and back side of the shell before firing.

They fit well and they work properly although the spring is a little weak. You can't hold them vertical and shake it cause then the shells will fall out although to an extend this happens with real clips too. 4/5 because they could be a little cheaper as the chance of loosing them during a skirm is way bigger compared to mags and you do need quite a few.

They look nice but it looks like there is to much play in the clip.
These may work on the standard replica but won't work on my replica due to the fact that I replaced the stock with a original stock for the k98.
Still and all i will still use them to store my shells for safekeeping.
There for they may still work for someone else