CM.107 Spike's Rare Breed Crusader Carbine [EMG]

The CM.107 Rare Breed airsoft carbine in a 13,2-inch configuration replicates the carbines of a well-known American company that was founded in 2004 in Maitland, Florida Spike's Tactical. This is an American firearms and parts manufacturer, including complete uppers, lower receivers, rifles, and barrels.

A project has been born

Due to a successful collaboration between two brands, EMG and Spikes Tactical a project of Airsoft rifle CM.107 was born. EMG for their ideas and the fact that they want to bring new products to the airsoft market. Spikes Tactical for their experience in real firearms. All this project was materialized by the airsoft gun manufacturer Cyma, which is popular for the quality of production and reasonable price.

An unusual airsoft rifle

Particular attention has been taken by EMG and Spikes Tactical to get a fully unusual rifle. So this airsoft rifle has been manufactured with MOD-ST15 standards. A full aluminum construction. A specific lower receiver from spike tactical can be found. A new Crusader design, the manufacturers were inspired by some of the most fierce warriors who fought in nearly 200 years of epic conflicts known as the Crusades.
This particular design gives a more realistic appearance and comes as close as possible to the real model.

A construction as close as possible to real

The CM.107 airsoft rifle is produced with high standards, with special attention to the material that has been used for the production. We got here a full metal construction, that depicts the fine detail and craftsmanship you would find on a real Spikes Tactical firearms receiver. This airsoft rifle is equipped with 13,2 inches CNC machined CRR Mlock system hand guards, which are not only aesthetic but incredibly ergonomic and lightweight. The Mlock attach system gives you the opportunity to mount and adapt different accessories.
On the top of the upper like on the handguard you can find a full-length 22 mm Picatinny rail system for optics or tactical flashlights. The 6-position polymer enhanced stock is equipped with a hatch at the rear to be able to install a battery more easily. The ergonomic of this rifle is given thanks to the QD attachments points, located at different locations on the rifle, 2 on each side of the handguard and 2 on the stock, this ensures the mounting of a tactical sling. All of these features make these guns not only look amazing but also perform outstanding right out of the box. However, this is not the only configuration that can be found, the airsoft rifle is available in two other models CM.107A and CM.107B

A reliable internal mechanism

The manufacturer Cyma platinum has already shown, on many occasions the innovations that can be brought to their gearboxes. The CM.107 in the new E-EDITION HIGH-SPEED configuration has a velocity of around 390 fps and, in combination with a high power LiPo battery, a ROF of around 25rps. An unical MOSFET in combination with low-resistance wires and a T-connector plug protects all the electrical installation. This was achieved due to the new gearbox parts with increased durability, such as:

• Reinforced V2 gearbox frame with quick spring change system
• Processor unit with built-in MOSFET system
• Full steel teeth polycarbonate piston
• CNC machined steel gear set (ratio: 13:1)
• 8mm ball bearings
• CNC machined aluminum silent cylinder and piston head set (ball bearing piston head, double o-ring cylinder head)
• Ball bearing spring guide
• A high-speed engine
• Metal rotary hop-up chamber

The set includes:

• CM.107 ST airsoft rifle
• 130rd magazine

Products recommended by us matching replica:

• Magazines:160RD M4/AR15 MID-CAP MAGAZINE, 300 RD HI-CAP STEEL MAGAZINE, 150RD MID-CAP STEEL MAGAZINE, 320RD HI-CAP STEEL MAGAZINE, M4 SERIES HI-CAP MAGAZINE FOR 400 BB`S.
• Batteries: BATTERY LI-PO 1300MAH 11,1V, BATTERY LI-PO 1300MAH 7,4V
When tuning your replica, we recommend replacing the gearbox shell with a gearbox made using the CNC method. Thanks to durable aluminum it is possible to use strong springs and the precision of manufacturing facilitates assembly and ensures the perfect fit of the parts. The suitable gearbox frame is CNC BILLET CM.097 V2 GEARBOX

Every replica passes initial check-up up. It's being checked and overshot on XCORTECH X3200 chronograph..